Sp-controls PixiePro Manual do Utilizador Página 1

PixiePro Device Control Module Installation GuidePX2-MP

V. WiringA. Wiring ControllerWiring PixiePro to Control a Single DeviceAttention! Remove power from the IR emitterbefore wiring to PixiePro. Do NOT a

2. Position IR bud over infrared-receiver window of the device to be controlled. Remove the back-ing to expose the adhesive and secure bud to IR recei

VI. ProgrammingA. OverviewThe PixiePro controls devices by learning and duplicating the IR codes of their remote controls.Each button may programmed w

C. Simple ProgrammingSimple programming assigns a single code to a button. 1. Press a Button on the PixiePro: Press the button you want to program a s

D. Complex Programming Complex programming assigns multiple codes to a single button, and defines how those codes willbe sent out. Each button may be

Stop and Delay ValuesDelays: Select Delay 0-0 through 3-7 to specify a delay between codes that are to be sent as amacro. After each delay has been en

Complex Programming: ExamplesExample 1: Program three individual codes to be sent in a round robin fashion (alternating codes onsubsequent button pres

To Erase a Single ButtonWhile in Learning Mode, press and hold a button that has been programmed to erase it. The buttonwill begin blinking slowly to

E. Programming the Transport Control/Menu Module (TCM) The Transport Control/Menu Module (TCM) may be configured for Single-Device or Multiple-Device

Final Test of Learned CodesVerify that the IR bud has been placed directly over the IR detector on the device the PixiePro con-trols. Press the PixieP

Important Safety Instructions1) Read these instructions. 2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not use this

VII. CloningCloning OverviewAny PixiePro may quickly copy all the programmed codes and configuration settings from any otherPixiePro wirelessly, or us

Cloning Procedure Using CAT5PixiePro units may be cloned using CAT5, CAT5e, or CAT6 cable, eliminating the need to hold theunits upright for the durat

VIII. ConfigurationOverviewConfiguration Mode is used to change the various settings on the PixiePro that control its behavior.By default, the setting

Configuration SettingsGroup 1 - Core Functions- Setting 1 - Multiple-Device TCM Mode - Setting 2 - “Device 0” on TCM in Multiple-Device Mode- Setting

Configuration Setting DescriptionsGroup 1 - Core FunctionsCore function settings determine behavior of PixiePro. Setting 1 - Multiple-Device TCM Mode

Group 2 - Timers Timer settings are used to configure a number of timer events on the PixiePro. Note: To deactivate any timer, set the timer value to

Timer Configuration Values Table230-00-10-20-30-40-50-60-71-01-11-21-31-41-51-61-72-02-12-22-32-42-52-62-73-03-13-23-33-43-53-63-7Auto Shutdown TimerO

Group 3 - SecuritySecurity settings are used to enable the secure mode on the PixiePro, and to modify the securitycode.Setting 1 - Enable/Disable Secu

Group 4 - Interface SettingsConfigure the “look and feel” of the PixiePro. Setting 1 - Button Click On/Off (toggle) Deselect Button Click to mute the

IX. OperationActively-programmed buttons will glow, indicating that they are ready for use. Press any button tosend the programmed IR command or serie

ContentsImportant Safety Instructions ...I. Overview ...

Technical Specifications Package Type: Four-Gang MountingApproximate Dimensions: 4.20" (h) x 7.10" (w) x 1.15" (d) (including button m

COPYRIGHTPixiePro™, and the SP Controls switch logo are trademarks of SP Controls, Inc. Belden™ is aBelden registered trademark. All other trademarks

I. OverviewWelcome to the user’s manual for your new PixiePro Modular Panel™! This manual documents allof the steps necessary to get the PixiePro up a

The flexible interface may be customized to your requirements. Most buttons may be replaced byblank button modules if unneeded. PixiePro can control a

II. Parts ListNote: Keep all button inserts and included materials, even if some modules are not currentlyused. They may be required in the future for

III. Assembly1. PreparationNote: When assembling the PixiePro, you will be working with a number of small parts. Be sure thatyou assemble the PixiePro

IV. InstallationPixiePro may be mounted using the plastic surface-mounting box (included), or using a standardfour-gang wall box (must be purchased se

3. Wall Flush MountingThe PixiePro may be flush mounted into a wall using either a standard four-gang back box and con-duit, or using a four-gang mud